This card has separate presets for the input and output settings under the ‘SYSTEM SETTINGS’ header. With this item you select how the IO presets are controlled: manually (Manual)
|IO_Prst_Act||With this item you can manually change the currently active IO settings. Can be any preset between 1 and
|IO_Prst_Edit||Here you can select which of the
With this item you can select which input you want to use
With this item you can select which input you want to use for Channel B.
With this item you can set the format of the CVBS input. Possible formats to select here are (default is Auto):
Auto (automatic detection and selection between NTSC-J and PAL-BGHID)
With Out-Frmt you can set what the output should be
With this setting you can select the 3Gb/s mapping in case the input format is 1080p50 or 1080p60. Can be manually set to Level A (default) or Level B. You can also choose to set it to auto, in which case the GDL will automatically detect whether the input is Level A or Level B.
With this setting you choose which input should be on which output. There are 4 available modes:
Straight (default): Channel A to outputs A1-A2, Channel B to outputs B1-B2
Crossed: Channel A to outputs B1-B2, Channel B to outputs A1-A2
A Only: Channel A to all outputs
B Only: Channel B to all outputs
When this setting is set to on, the input selection will switch when the active input is lost. Set to off will not switch the input on input loss. Set to once, the switch will only be done once, and will not switch back when the input fails again. Default is on.
F-Delay sets the number of delayed Frames. The available range is from 0 to
V-Delay setting allows adjustment of the vertical phase of the output signal with respect to the selected reference input.
The V-Delay setting gives a delay in addition to the reference timing. For example: if the V-Delay is set to 10 TV HD lines, the output signal will be delayed by reference timing + 10 TV HD lines. The signal is delayed (advanced) with respect to the phase of the reference signal. The available range is from 0 to a maximum of 1125 lines (dependent on I/O format). The default setting is 0ln.
The H-Delay setting allows adjustment of the Horizontal phase of the output signal with respect to the selected reference input.
The H-Delay setting gives a delay in addition to the reference timing. For example: if the H-Delay is set to 10 pixels, the output signal will be delayed by reference timing + 10 pixels. The signal is delayed (advanced) with respect to the phase of the reference signal. The available range is from 0 to a maximum of 5124 pixels (dependent on I/O format). The default setting is 0px.
|#Freeze_A||Freeze enables the capture of one Video
|#Freeze_B||Freeze_B enables the capture of one Video
It is possible to display the processing time of the card in the Status menu. This setting allows you to switch this function On or Off (default).
Lock-Mode determines whether the card is locked to its input , to the reference (Ref1 or Ref2)
When set to RefAuto the card chooses ref1 as its source. Whenever ref1 fails, it will switch to ref 2 (only for SFR08 and SFR18 frames and only when ref2 offers the same ref format as ref 1). When ref 1 is back up again, it will only automatically switch back to ref 1 when ref 2 fails.
|Ref-Type||Sets the type of incoming reference. Can be either Bi-Level (default) or Tri- Level.|
|P60-P50_Sync||With this setting you can choose to synchronize each one frame or each two frames. Default is One Frame. The two-frame-synchronize mode only works for 720p60, 720p50, 1080p50 and 1080p60 standards.|
|ANC_BlankA||With this setting you can Blank the vertical ancillary data only (V-Only), blank the horizontal ancillary data only (H-only) or blank both vertical and horizontal ancillary data (H_And_V). You can also choose to not blank any data (Off), which is also default.|
|ANC_BlankB||With this setting you can Blank the vertical ancillary data only (V-Only), blank the horizontal ancillary data only (H-only) or blank both vertical and horizontal ancillary data (H_And_V). You can also choose to not blank any data (Off), which is also default. This setting is for Channel B only.|
|Freeze_Mode||Freeze_Mode allows you to choose between storing a complete Video Frame or Field (double written) in case of a video freeze. The default setting is Field.|
With this setting set to Follow Active, the edit preset settings (e.g. UP_Prst_editA and UP_Prst_editB) will follow the active preset when the active preset is changed. This is to avoid confusion when changing the active preset. Set to Independent, the edit preset will not automatically follow active preset changes. By default set to Follow Active.
|PatternSpeed||Sets the speed of the test-pattern (see settings Inp_SelA and Inp_SelB) animation between 0 (still) and 1
Freeze: a capture of the last good field or frame.
Colorbar: a color bar
Zoneplate: a zone plate
Black: a black output.
Grey: a gray output.
Green: a green output.
Freeze 1 sec: a freeze of the last field or frame for 1 second. After 1 second the output framework is disabled.
Freeze 5 sec: Same as Freeze 1 sec, only holding the freeze frame/field for 5 seconds.
The default setting is Freeze.
|Input_Loss_B||Input_loss_B determines what the output of output B is in case of lost input. Same values as Input_Loss_A are possible.|